Certex Logo

Categories

Pyramex – RVZ28 Series

Pyramex - RVZ28 Series


ANSI
Black trim // Clear chest pocket for badges with hook and loop closure // Tablet pockets (12″ x 7″) with hook and loop closures // Reach-through pocket on back with zipper closures // Metal grommets on upper front collar trim // Mic tab // Sizes M-5XL
RVZ2810 / RVZ2820

MATERIALS

Vest: 100% polyester, 105gsm polyester mesh
Pocket 100% polyester, 120gsm solid knit
Reflective Tape: Generic Silver

CLOSURE

Front: SBS Zipper
Zipper Tape: 100% polyester fabric
Zipper Teeth: Resin
Zipper Slider: Metal

REFLECTIVE STRIPING

One 2” stripe of reflective material applied horizontally 6” from bottom of vest
One 2” silver reflective stripe applied horizontally 3” from bottom stripe on back
One 2” silver reflective stripe applied horizontally 5.5” from top of shoulder on front
Two 2” silver reflective stripes run vertically from top of horizontal stripes

POCKETS

One reach through pocket on back with zipper closure: 23” x 12”
Two lower front pockets with flap hook and loop closure: 8.5” x 13”
One upper left chest double pocket divided into four parts: 5.5” x 5”
One upper right chest pocket with clear PVC front with flap closure: 4” x 7”
One inside lower left pocket with hook and loop closure: 13” x 7”
One inside lower right pocket with hook and loop closure: 13” x 7”
One inside upper left pocket with flap hook and loop closure: 4.4” x 6”

SPECIAL FEATURES

Double tacked 1” x 2.5” badge/mic holder located 4” from the center shoulder seam on both sides
Two metal grommets on upper front collar trim

VEST MEASUREMENTS

SIZE M L XL 2X 3X 4X 5X
CHEST MEASUREMENT 25” 26” 28.5” 30” 32” 34” 36”

Vest measurements are taken while garment is lying flat.
Please note: some size variation may occur.

WARNING: Prop 65: Products supplied by CERTEX USA may expose you to chemicals including Nickel, which is known to the State of California to cause cancer. For more information, visit to www.P65Warnings.ca.gov.

Related Products

Caldwell Adjustable Lifting Beam, Economy Model 17

Caldwell Adjustable Lifting Beam, Economy Model 17

Model 17 Adjustable Lifting beam features an adjustable bail and lifting points in 6" incerments to handle standard and unbalanced loads. Get the set-up you need with a few quick motions. Features: Bail adjusts horizontally for lifting unbalanced loads Provides...

Caldwell Dura-Lite Composite Adjustable Lifting Beams Model 416

Caldwell Dura-Lite Composite Adjustable Lifting Beams Model 416

Dura-Lite Model 416 is the composit version of Caldwell's Model 16 Adjustable Lifting Beam. Choose for corrosive enviroments, areas where sparks are a concern, or when a lighter beam allows you to pick a heavier load. Features: Lightweight beam gives you additional...

Caldwell Die Lifting Tongs Model DLT

Caldwell Die Lifting Tongs Model DLT

Support Tongs are used for repeat pickups of constant-sized containers such as boxes and crates. The arm design allows significant height on the lifted item and the Auto-Latch mechanism allows the operator to position, engage, lift, move, place, and disengage the...

Caldwell Dixon Coil Hook with Pivoting Wedge Model 80H

Caldwell Dixon Coil Hook with Pivoting Wedge Model 80H

It's all about the pivoting wedge on this unit. By maneuvering that wedge in between two stacked coils, an operator can separate them and begin a tilt, allowing the rest of the hook to slide in and do its job. Features: Easy horizontal to vertical upending of coils...