Leading the lifting & rigging industry
Certex Logo

Categories

Associated Wire Rope Standard Reeve Crane Blocks

Associated Wire Rope Standard Reeve Crane Blocks

Blocks shown in this section may be used on a wide variety of land based cranes such as mobile and crawler cranes. Standard Reeve Blocks are an excellent choice where frequent easy block change is not a required main feature, or lifting height is limited:

  • Double sealed maintenance free roller bearings
  • Design Factor of Safety of 4:1
  • Forged high tensile steel DIN hooks
  • Sheaves featuring graphite lubricated groove
  • High impact resistant side plates
  • Operational temperature range: -40 up to +80°C / -40 up to +176°F
  • Lubrication on hook suspension
  • Short design for increased lifting height
  • Safety latch with locking pin
  • C3M finish in signal yellow

EMAIL PAGE

EMAIL PAGE

WARNINGS & CAUTIONS

WARNINGS & CAUTIONS

1-Sheave

Model No. WLL
(UStons)		 For Wire ød
(inch)		 Hook Size Dimensions (inch) Weight (lbs)
øD1 øD2 B O TA TL L T øZ
SRB 225.xx.1.12,5.E 13.7 3/8 – 9/16 5 10.2 8.9 20.6 2.5 13.6 31.4 35.9 TBD TBD 165
SRB 260.xx.1.12,5.E 13.7 7/16 – 5/8 5 11.8 10.2 21.6 2.5 15.7 32.8 37.3 TBD TBD 240
SRB 225.xx.1.16.E 17.6 3/8 – 9/16 6 10.2 8.9 21.6 2.5 13.6 32.4 36.9 TBD TBD 220
SRB 260.xx.1.16.E 17.6 7/16 – 5/8 6 11.8 10.2 21.6 2.5 15.7 32.8 37.3 TBD TBD 240
SRB 285.xx.1.16.E 17.6 1/2 – 3/4 6 12.6 11 23.9 2.8 16.5 35.7 40.7 TBD TBD 350
SRB 320.xx.1.16.E 17.6 9/16 – 3/4 6 14.4 12.6 24.7 2.8 17.7 37.4 42.6 TBD TBD 350
SRB 355.xx.1.16.E 17.6 9/16 – 7/8 6 16.1 14 26.3 2.8 19.7 39.9 44.8 TBD TBD 400
SRB 320.xx.1.20.E 22 9/16 – 3/4 8 14.4 12.6 27.1 3.1 17.7 39.8 45.4 TBD TBD 350
SRB 355.xx.1.20.E 22 9/16 – 7/8 8 16.1 14 28.1 3.1 19.7 41.5 47.4 TBD TBD 550
SRB 450.xx.1.25.E 27.5 3/4 – 11/8 8 20.3 17.7 30.3 3.1 23.6 46.8 52.9 TBD TBD 435
SRB 528.xx.1.28.E 30 7/8 – 11/4 8 23.5 20.8 33 3.1 27.9 52 58.6 TBD TBD 600
SRB 400.xx.1.29.E 32 5/8 – 1 8 18.1 15.7 29.3 3.1 22.4 44.4 50.1 TBD TBD 640
SRB 450.xx.1.32.E 35 3/4 – 11/8 10 20.3 17.7 32.8 3.5 23.6 49.4 56 TBD TBD 1000 | 1100
SRB 528.xx.1.32.E 35 7/8 – 11/4 10 23.5 20.8 35.4 3.5 28 53.6 60.2 TBD TBD 1100 | 1400 | 2000
SRB 450.xx.1.40.E 45 3/4 – 11/8 12 20.3 17.7 42.3 3.9 23.6 58.5 65.6 TBD TBD 1300
SRB 450.xx.1.50.E 55 3/4 – 11/8 12 20.3 17.7 36.1 3.9 23.8 52.7 59.7 TBD TBD 1300
SRB 528.xx.1.50.E 55 7/8 – 11/4 12 23.5 20.8 36.8 3.9 28 55.6 63.1 TBD TBD 1650
SRB 575.xx.1.50.E 55 15/16 – 11/4 12 25.6 22.6 37.7 3.9 30.3 57.4 65.4 TBD TBD 2045
SRB 630.xx.1.64.E 70 1 – 13/8 16 28.3 24.8 38.8 4.4 32.5 59.9 68 TBD TBD 2200
SRB 670.xx.1.64.E 70 1 – 11/2 16 29.9 26.4 46.2 4.4 34.3 68.4 76.6 TBD TBD 3000

Minimum Ultimate Strength = 4 x WLL

  • The dimensions in this table are indicative only. A drawing will always be submitted prior to  production and will be the leading document when discussing dimensions.
  • Blocks shown here are standard models; inquiries for custom versions are welcome.
  • Refer to wire rope manufacturers D/d ratio guideline.
  • Optional: Hook locking pin.

2-Sheave

Model No. WLL
(UStons)		 For Wire ød
(inch)		 Hook Size Dimensions (inch) Weight (lbs)
øD1 øD2 B O TA TL L T øZ
SRB 225.xx.2.16.E 17.6 3/8 – 9/16 6 11.8 10.2 23.3 2.8 15.7 34.6 39.5 TBD TBD 240
SRB 260.xx.2.16.E 17.6 7/16 – 5/8 6 11.8 10.2 23.3 2.8 15.7 34.6 39.5 TBD TBD 285
SRB 285.xx.2.16.E 17.6 1/2 – 3/4 6 12.6 11 23.9 2.8 16.5 35.7 40.7 TBD TBD 210
SRB 260.xx.2.20.E 22 7/16 – 5/8 8 11.8 10.2 26.7 3.1 15.7 43 38 TBD TBD 285 | 350
SRB 285.xx.2.20.E 22 1/2 – 3/4 8 12.6 11 26.3 3.1 16.5 38.1 43.4 TBD TBD 285 | 330
SRB 320.xx.2.20.E 22 9/16 – 3/4 8 14.4 12.6 27.1 3.1 17.7 39.8 45.1 TBD TBD 350
SRB 320.xx.2.22.E 24 9/16 – 3/4 8 14.4 12.6 27.1 3.1 17.7 39.8 45.6 TBD TBD 350
SRB 260.xx.2.25.E 27.5 7/16 – 5/8 8 11.8 10.2 26.5 3.1 15.7 37.7 42.8 TBD TBD 350
SRB 320.xx.2.25.E 27.5 9/16 – 3/4 8 14.4 12.6 27.1 3.1 17.7 39.8 45.1 TBD TBD 450
SRB 355.xx.2.29.E 32 9/16 – 7/8 8 16.1 14 28.1 3.1 19.7 41.9 47.4 TBD TBD 550
SRB 400.xx.2.29.E 32 5/8 – 1 8 18.1 15.7 29.3 3.1 22.4 44.4 50.1 TBD TBD 705
SRB 450.xx.2.40.E 45 3/4 – 11/8 12 20.3 17.7 35.2 3.9 23.6 52 58.1 TBD TBD 1210
SRB 450.xx.2.50.E 55 3/4 – 11/8 12 20.3 17.7 35.2 3.9 23.6 52 59.6 TBD TBD 1210
SRB 400.xx.2.55.E 60 5/8 – 1 12 18.1 15.7 34 3.9 22.4 48.9 55.6 TBD TBD 800
SRB 528.xx.2.64.E 70 7/8 – 11/4 16 23.4 20.8 39.5 4.4 28 58.4 65.9 TBD TBD 2155
SRB 528.xx.2.80.E 88 7/8 – 11/4 20 23.4 20.8 43.7 4.9 28 62.6 71.2 TBD TBD 2200
SRB 670.xx.2.100.E 110 1 – 13/8 20 29.9 26.4 49.5 4.9 34.3 71.7 80.4 TBD TBD 4930

Minimum Ultimate Strength = 4 x WLL

  • The dimensions in this table are indicative only. A drawing will always be submitted prior to  production and will be the leading document when discussing dimensions.
  • Blocks shown here are standard models; inquiries for custom versions are welcome.
  • Refer to wire rope manufacturers D/d ratio guideline.
  • Optional: Hook locking pin.

3-Sheave

Model No. WLL
(UStons)		 For Wire ød
(inch)		 Hook Size Dimensions (inch) Weight (lbs)
øD1 øD2 B O TA TL L T øZ
SRB 260.xx.3.25.E 27.5 7/16 – 5/8 8 11.8 10.2 25.9 3.1 15.7 37.5 42.8 TBD TBD 465
SRB 285.xx.3.29.E 32 1/2 – 3/4 8 12.8 11.2 26.3 3.1 15.7 38.5 43.8 TBD TBD 465
SRB 320.xx.3.29.E 32 9/16 – 3/4 8 14.4 12.6 28.1 3.1 17.7 41.3 46.6 TBD TBD 495
SRB 355.xx.3.32.E 35 9/16 – 7/8 10 16.1 14 29.6 3.5 19.7 43 49 TBD TBD 715
SRB 360.xx.3.40.E 44 5/8 – 7/8 12 16.1 14.2 33 3.9 19.7 46.4 52.8 TBD TBD 1000
SRB 400.xx.3.40.E 44 5/8 – 1 12 18.1 15.7 34 3.9 22.4 49 55.6 TBD TBD 1100
SRB 400.xx.3.50.E 55 5/8 – 1 12 18.1 15.7 34 3.9 22.4 49 56.1 TBD TBD 1100 | 1200
SRB 450.xx.3.50.E 55 3/4 – 11/8 16 20.3 17.7 38.6 4.4 23.6 53.5 60.3 TBD TBD 1450
SRB 360.xx.3.55.E 60 5/8 – 7/8 12 16.1 14.2 33 3.9 19.7 46.4 52.9 TBD TBD 1000
SRB 400.xx.3.55.E 60 5/8 – 1 12 18.1 15.7 34 3.9 22.4 49 55.6 TBD TBD 1200
SRB 450.xx.3.64.E 70 3/4 – 11/8 16 20.3 17.7 37.9 4.4 23.6 54.2 61.3 TBD TBD 1500 | 1700
SRB 450.xx.3.70.E 77 3/4 – 11/8 16 20.3 17.7 38.3 4.4 23.6 55 62.9 TBD TBD 1500 | 1650
SRB 528.xx.3.82.E 90 7/8 – 11/4 20 23.4 20.8 44.6 4.9 28 63.5 71.7 TBD TBD 2500
SRB 528.xx.3.100.E 110 7/8 – 11/4 25 23.4 20.8 48.1 5.5 28 66.3 75.3 TBD TBD 2800
SRB 670.xx.3.125.E 137.5 1 – 13/8 25 29.9 26.4 53.3 5.5 34.3 75.5 85 TBD TBD 6380

Minimum Ultimate Strength = 4 x WLL

  • The dimensions in this table are indicative only. A drawing will always be submitted prior to production and will be the leading document when discussing dimensions.
  • Blocks shown here are standard models; inquiries for custom versions are welcome.
  • Refer to wire rope manufacturers D/d ratio guideline.
  • Optional: Hook locking pin.

4-Sheave

Model No. WLL
(UStons)		 For Wire ød
(inch)		 Hook Size Dimensions (inch) Weight (lbs)
øD1 øD2 B O TA TL L T øZ
SRB 285.xx.4.35.E 38.5 1/2 – 3/4 10 12.8 11.2 26 3.5 15.7 36.2 40.4 TBD TBD 570
SRB 355.xx.4.50.E 55 9/16 – 7/8 12 16.1 14 33 3.9 19.7 43.9 50.8 TBD TBD 1045
SRB 528.xx.4.55.E 60 7/8 – 11/4 12 23.5 20.8 38.5 3.9 28 53.5 60.6 TBD TBD 2600
SRB 400.xx.4.64.E 70 5/8 – 1 16 18.1 15.7 35.6 4.4 22.4 47.2 54.4 TBD TBD 1155
SRB 450.xx.4.64.E 70 3/4 – 11/8 16 20.3 17.7 38 4.4 23.6 52 59.2 TBD TBD 1595
SRB 528.xx.4.70.E 77 7/8 – 11/4 16 23.5 20.8 40.4 4.4 28 55.3 63 TBD TBD 3850
SRB 450.xx.4.82.E 90 3/4 – 11/8 20 20.3 17.7 41.2 4.9 23.6 51.6 59.8 TBD TBD 2110
SRB 450.xx.4.82.E 90 3/4 – 11/8 20 20.3 17.7 41.2 4.9 23.6 51.6 59.8 TBD TBD 2110
SRB 528.xx.4.105.E 115 7/8 – 11/4 25 23.4 20.8 48.1 5.5 28 62.7 71.8 TBD TBD 3900
SRB 710.xx.4.105.E 115 11/8 – 11/2 25 31.5 28 53.3 5.5 35.4 73.9 84.4 TBD TBD 3000
SRB 450.xx.4.108.E 120 3/4 – 11/8 25 20.3 17.7 46.8 5.5 23.6 60.2 68.9 TBD TBD 3200
SRB 670.xx.4.160.E 176 1 – 13/8 40 29.9 26.4 60.7 7.1 34.3 82.9 94 TBD TBD 6930

Minimum Ultimate Strength = 4 x WLL

  • The dimensions in this table are indicative only. A drawing will always be submitted prior to production and will be the leading document when discussing dimensions.
  • Blocks shown here are standard models; inquiries for custom versions are welcome.
  • Refer to wire rope manufacturers D/d ratio guideline.
  • Optional: Hook locking pin.

5-Sheave

Model No. WLL
(UStons)		 For Wire ød
(inch)		 Hook Size Dimensions (inch) Weight (lbs)
øD1 øD2 B O TA TL L T øZ
SRB 355.xx.5.55.E 60 9/16 – 7/8 12 16.1 14 33 4.4 19.7 44.6 51.4 TBD TBD 1100
SRB 360.xx.5.64.E 70 5/8 – 7/8 16 16.1 14.2 39.1 4.4 19.7 47.2 54.1 TBD TBD 1320
SRB 528.xx.5.70.E 77 7/8 – 11/4 16 23.4 20.8 40.8 4.4 27.9 55.7 63.1 TBD TBD 2800
SRB 400.xx.5.73.E 80 5/8 – 1 16 18.1 15.7 37.6 4.4 22.4 49.6 56.7 TBD TBD 1650
SRB 360.xx.5.80.E 88 5/8 – 7/8 20 16.1 14.2 39.1 4.9 19.7 50.5 58.1 TBD TBD 1805
SRB 400.xx.5.82.E 90 5/8 – 1 20 18.1 15.7 40.7 4.9 22.4 53.7 61.6 TBD TBD 1800
SRB 450.xx.5.82.E 90 3/4 – 11/8 20 20.3 17.7 42.2 4.9 23.6 56.3 64.2 TBD TBD 2250
SRB 450.xx.5.100.E 110 3/4 – 11/8 25 20.3 17.7 44.4 5.5 23.6 58.5 67.6 TBD TBD 2500
SRB 528.xx.5.125.E 137.5 7/8 – 11/4 32 23.4 20.8 49.7 6.3 28 66.8 76.6 TBD TBD 3500
SRB 528.xx.5.137,5.E 150 7/8 – 11/4 32 23.4 20.8 52.5 6.3 28 50.1 77.8 TBD TBD 3500
SRB 528.xx.5.160.E 176 7/8 – 11/4 40 23.4 20.8 55.4 7.1 28 70.7 81.8 TBD TBD 3640
FRB 670.xx.5.200.E 220 1 – 13/8 50 29.9 26.4 64.6 7.9 34.3 83.9 95.9 TBD TBD 7830

Minimum Ultimate Strength = 4 x WLL

  • The dimensions in this table are indicative only. A drawing will always be submitted prior to production and will be the leading document when discussing dimensions.
  • Blocks shown here are standard models; inquiries for custom versions are welcome.
  • Refer to wire rope manufacturers D/d ratio guideline.
  • Optional: Hook locking pin.

WARNING: Prop 65: Products supplied by CERTEX USA may expose you to chemicals including Nickel, which is known to the State of California to cause cancer. For more information, visit to www.P65Warnings.ca.gov.

Related Products

Associated Wire Rope Snatch Blocks

Associated Wire Rope Snatch Blocks

Ropeblock Snatch Blocks are an excellent choice in most rigging and lifting plans. Durability and ease of use are some of the key benefits in addition to: Design Factor of Safety of 4:1 Lubricated bronze bushings Eye or oblong eye connection Sheaves, featuring...

Associated Wire Rope Round Overhaul Balls

Associated Wire Rope Round Overhaul Balls

The weight of the overhaul balls in this segment are based on average boom lengths and efficiency loss in mobile and crawler cranes. The low friction and easy to access hook swivel design makes the OHB series an excellent choice for a wide variety of crane...

Associated Wire Rope Overhaul Balls

Associated Wire Rope Overhaul Balls

The weight of the overhaul balls in this segment are based on average boom lengths and efficiency loss in mobile and crawler cranes. The low friction and easy to access hook swivel design makes the OHB series an excellent choice for a wide variety of crane...

Associated Wire Rope Fast Reeve Crane Blocks

Associated Wire Rope Fast Reeve Crane Blocks

Blocks shown in this section may be used on a wide variety of land based cranes such as mobile and crawler cranes. The Fast Reeve Blocks are an excellent choice for your lifting application where frequent block change is required and includes the following standard...