Leading the lifting & rigging industry
Certex Logo

Categories

Associated Wire Rope Fast Reeve Crane Blocks

Associated Wire Rope Fast Reeve Crane Blocks

Blocks shown in this section may be used on a wide variety of land based cranes such as mobile and crawler cranes. The Fast Reeve Blocks are an excellent choice for your lifting application where frequent block change is required and includes the following standard features:

  • Design Factor of Safety of 4:1
  • Double sealed maintenance free roller bearings
  • Forged high tensile steel DIN hooks
  • Sheaves featuring graphite lubricated groove
  • High impact resistant side plates
  • Operational temperature range: -40 up to +80°C / -40 up to +176°F
  • Lubrication on hook suspension
  • 4 or 8 point hook locking device
  • Fast Reeve guides for fast reeving
  • C3M finish in signal yellow with black striping
  • Safety latch with locking pin

EMAIL PAGE

EMAIL PAGE

WARNINGS & CAUTIONS

WARNINGS & CAUTIONS

1-Sheave

Model No. WLL
(UStons)		 For Wire ød
(inch)		 Hook
Size		 Dimensions (inch) Weight (lbs)
øD1 øD2 B O TA TL L T øZ
FRB 225.xx.1.12,5.E 13.7 3/8 – 9/16 4 10.2 8.9 23.1 2.2 13.6 34 38.2 TBD TBD 195
FRB 260.xx.1.12,5.E 13.7 7/16 – 5/8 4 11.8 10.2 25.7 2.2 15.7 36.9 41.9 TBD TBD 220
FRB 225.xx.1.16.E 17.6 3/8 – 9/16 6 10.2 8.9 23.9 2.8 13.6 34.8 39.7 TBD TBD 225
FRB 260.xx.1.16.E 17.6 7/16 – 5/8 6 11.8 10.2 27.3 2.8 15.7 38.5 43.4 TBD TBD 265 | 325 | 375
FRB 285.xx.1.16.E 17.6 1/2 – 3/4 6 12.6 11.2 28.5 2.8 16.5 40.3 45.2 TBD TBD 350
FRB 320.xx.1.16.E 17.6 9/16 – 3/4 6 14.4 12.6 28.7 2.8 17.7 41.8 16.8 TBD TBD 350
FRB 355.xx.1.16.E 17.6 9/16 – 7/8 6 16.1 14 31 2.8 19.7 44.6 49.7 TBD TBD 500 | 550
FRB 260.xx.1.20.E 22 7/16 – 5/8 8 11.8 10.2 29.4 3.1 15.7 40.7 46 TBD TBD 285 | 375 | 425
FRB 285.xx.1.20.E 22 1/2 – 3/4 8 12.6 11.2 30.6 3.1 16.5 42.4 47.8 TBD TBD 350
FRB 320.xx.1.20.E 22 9/16 – 3/4 8 14.4 12.6 30.2 3.1 17.7 43.3 48.7 TBD TBD 350 | 425 | 475
FRB 355.xx.1.20.E 22 9/16 – 7/8 8 16.1 14 33.6 3.1 19.7 47.2 52.5 TBD TBD 550 | 660
FRB 355.xx.1.25.E 27.5 9/16 – 7/8 8 16.1 14 33.4 3.1 19.7 47 52.5 TBD TBD 550 | 750
FRB 400.xx.1.25.E 27.5 5/8 – 1 8 18.1 15.7 34.8 3.1 22.4 49.5 55.2 TBD TBD 700 | 750
FRB 400.xx.1.26.E 28.5 5/8 – 1 8 18.1 15.7 34.8 3.1 22.4 49.5 55.2 TBD TBD 1100
FRB 400.xx.1.29.E 32 5/8 – 1 8 18.1 15.7 34.8 3.1 22.4 49.9 55.6 TBD TBD 800
FRB 450.xx.1.29.E 32 3/4 – 1 1/8 8 20.3 17.7 37.3 3.1 23.6 51.4 59.3 TBD TBD 650 | 800
FRB 450.xx.1.32.E 35 3/4 – 1 1/8 10 20.3 17.7 39.5 3.5 23.6 56.1 62.7 TBD TBD 1100 | 1320
FRB 528.xx.1.32.E 35 7/8 – 1 1/4 10 23.4 20.8 40.5 3.5 28 58.7 65.3 TBD TBD 1100 | 1320 | 1500 | 1800
FRB 670.xx.1.32.E 35 1 – 1 1/2 10 29.9 26.4 41.3 3.5 34.3 63.3 70.3 TBD TBD 1700
FRB 450.xx.1.40.E 45 3/4 – 1 1/8 12 20.3 17.7 42.3 3.9 23.6 58.9 65.9 TBD TBD 1300 | 1500
FRB 528.xx.1.40.E 45 7/8 – 1 1/4 12 23.4 20.8 43.9 3.9 28 62.7 69.7 TBD TBD 1500 | 1700 | 1875 | 2000
FRB 450.xx.1.50.E 55 3/4 – 1 1/8 12 20.3 17.7 43.1 3.9 23.6 59.6 67.2 TBD TBD 1300 | 1500
FRB 528.xx.1.50.E 55 7/8 – 1 1/4 12 23.4 20.8 43.7 3.9 28 62.6 70.1 TBD TBD 1500 | 1700 | 1875 | 2000
FRB 575.xx.1.50.E 55 15/16 – 1 1/4 12 25.6 22.6 45 3.9 30.3 64.9 72.9 TBD TBD 2200
FRB 630.xx.1.50.E 55 1 – 1 3/8 12 27.9 24.8 43.6 3.9 35.4 64.7 72.1 TBD TBD 1800 / 3500 / 5300*
FRB 670.xx.1.50.E 55 1 – 1 1/2 12 29.9 26.4 44.1 3.9 34.3 66.3 73.7 TBD TBD 2000 | 2600 | 3000
FRB 670.xx.1.64.E 70 1 – 1 1/2 16 29.9 26.4 49.1 4.4 34.3 71.4 79.3 TBD TBD 2200 | 2600 | 3000

* Removable cheek weights
Minimum Ultimate Strength = 4 x WLL

  • The dimensions in this table are indicative only. A drawing will always be submitted prior to production and will be the leading document when discussing dimensions.
  • Blocks shown here are standard models; inquiries for custom versions are welcome.
  • Refer to wire rope manufacturers D/d ratio guideline.
  • Optional: Hook locking pin.

2-Sheave

 

Model No. WLL
(UStons)		 For Wire ød
(inch)		 Hook
Size		 Dimensions (inch) Weight (lbs)
øD1 øD2 B O TA TL L T øZ
FRB 225.xx.2.16.E 17.6 3/8 – 9/16 6 10.2 8.9 23.9 2.8 13.6 34.8 39.7 TBD TBD 265
FRB 260.xx.2.16.E 17.6 7/16 – 5/8 6 11.8 10.2 27.3 2.8 15.7 38.5 43.4 TBD TBD 285 | 350
FRB 225.xx.2.20.E 22 3/8 – 9/16 8 10.2 8.9 28.3 3.1 13.6 37.7 43.1 TBD TBD 285
FRB 260.xx.2.20.E 22 7/16 – 5/8 8 11.8 10.2 29.4 3.1 15.7 40.7 46 TBD TBD 285 | 350 | 425
FRB 260.xx.2.25.E 27.5 7/16 – 5/8 8 11.8 10.2 29.3 3.1 15.7 40.5 45.6 TBD TBD 350 | 425
FRB 320.xx.2.25.E 27.5 9/16 – 3/4 8 14.4 12.6 30 3.1 17.7 43.1 48.5 TBD TBD 450 | 495
FRB 320.xx.2.29.E 32 9/16 – 3/4 8 14.4 12.6 30.1 3.1 17.3 43.1 48.5 TBD TBD 600
FRB 355.xx.2.29.E 32 9/16 – 7/8 8 16.1 14 33.4 3.1 19.7 47 52.5 TBD TBD 585 | 625 | 750
FRB 400.xx.2.32.E 35 5/8 to 1 10 18.1 15.7 37.5 3.5 22.4 52.7 58.9 TBD TBD 800
FRB 450.xx.2.32.E 35 3/4 – 1 1/8 10 20.3 17.7 39.5 3.5 23.6 55.7 61.9 TBD TBD 1100
FRB 450.xx.2.46.E 50 3/4 – 1 1/8 12 20.3 17.7 42.2 3.9 23.6 58.5 65.2 TBD TBD 1200
FRB 450.xx.2.55.E 60 3/4 – 1 1/8 16 20.3 17.7 42.3 4.4 23.6 58.9 66.5 TBD TBD 1600
FRB 528.xx.2.55.E 60 7/8 – 1 1/4 12 23.4 20.8 43.8 3.9 27.9 62.6 70.1 TBD TBD 2000
FRB 670.xx.2.55.E 60 1 – 1 1/2 12 29.9 26.4 44.2 3.9 34.3 67 74.1 TBD TBD 2080
FRB 528.xx.2.70.E 77 7/8 – 1 1/4 16 23.4 20.8 47.3 4.4 28 65.2 72.8 TBD TBD 2200
FRB 670.xx.2.82.E 90 1 – 1 1/2 20 29.9 26.4 50.7 4.9 34.3 74.7 83.6 TBD TBD 3400

Minimum Ultimate Strength = 4 x WLL

  • The dimensions in this table are indicative only. A drawing will always be submitted prior to  production and will be the leading document when discussing dimensions.
  • Blocks shown here are standard models; inquiries for custom versions are welcome.
  • Refer to wire rope manufacturers D/d ratio guideline.
  • Optional: Hook locking pin.

3-Sheave

Model No. WLL
(UStons)		 For Wire ød
(inch)		 Hook
Size		 Dimensions (inch) Weight (lbs)
øD1 øD2 B O TA TL L T øZ
FRB 225.xx.3.20.E 22 3/8 – 9/16 8 10.2 8.9 28.3 3.1 13.6 39.1 44.4 TBD TBD 410
FRB 260.xx.3.20.E 22 7/16 – 5/8 8 11.8 10.2 28.5 3.1 15.7 40.1 45.4 TBD TBD 410
FRB 260.xx.3.25.E 27.5 7/16 – 5/8 8 11.8 10.2 27.5 3.1 15.7 39.1 44.4 TBD TBD 465
FRB 285.xx.3.29.E 32 1/2 – 3/4 8 12.6 11 27.7 3.5 16.5 39.9 45.2 TBD TBD 460
FRB 320.xx.3.29.E 32 9/16 – 3/4 8 14.4 12.6 30 3.1 17.7 43.1 48.5 TBD TBD 505
FRB 260.xx.3.32.E 35 7/16 – 5/8 10 11.8 10.2 28.9 3.5 15.7 40.5 46.3 TBD TBD 465
FRB 285.xx.3.32.E 35 1/2 – 3/4 10 12.6 11 30 3.5 16.5 42.2 48 TBD TBD 460 | 505
FRB 320.xx.3.32.E 35 9/16 – 3/4 10 14.4 12.6 32.2 3.5 17.7 45.3 51.1 TBD TBD 505 | 625
FRB 320.xx.3.37.E 40 9/16 – 3/4 10 14.4 12.6 32.2 3.5 17.7 45.3 51.1 TBD TBD 700
FRB 355.xx.3.37.E 40 9/16 – 7/8 10 16.1 14 34 3.5 19.7 48 53.7 TBD TBD 700 | 825
FRB 360.xx.3.41 .E 45 5/8 – 7/8 12 16.5 14.2 35.4 3.9 20.1 49.3 55.8 TBD TBD 900
FRB 360.xx.3.46.E 50 5/8 – 7/8 12 16.5 14.2 35.4 3.9 20.1 49.3 55.8 TBD TBD 900
FRB 400.xx.3.46.E 50 5/8 to 1 12 18.1 15.7 37.3 3.9 22.4 52.1 58.6 TBD TBD 1000
FRB 360.xx.3.50.E 55 5/8 – 7/8 12 16.5 14.2 35.4 3.9 20.1 49.4 56.3 TBD TBD 900 | 1200
FRB 400.xx.3.50.E 55 5/8 to 1 12 18.1 15.7 37.4 3.9 22.4 52.1 59.1 TBD TBD 1100 | 1200 | 1350
FRB 360.xx.3.55.E 60 5/8 – 7/8 12 16.5 14.2 35.4 3.9 20.1 49.3 55.8 TBD TBD 900 | 1200
FRB 400.xx.3.55.E 60 5/8 to 1 12 18.1 15.7 37.4 3.9 22.4 52.1 59.1 TBD TBD 1100 | 1200 | 1350

Minimum Ultimate Strength = 4 x WLL

  • The dimensions in this table are indicative only. A drawing will always be submitted prior to production and will be the leading document when discussing dimensions.
  • Blocks shown here are standard models; inquiries for custom versions are welcome.
  • Refer to wire rope manufacturers D/d ratio guideline.
  • Optional: Hook locking pin.

4-Sheave

 

Model No. WLL
(UStons)		 For Wire ød
(inch)		 Hook Size Dimensions (inch) Weight (lbs)
øD1 øD2 B O TA TL L T øZ
FRB 355.xx.4.35.E 38.5 9/16 – 7/8 10 16.1 14 36.7 3.5 19.7 47.4 53.1 TBD TBD 925
FRB 320.xx.4.37.E 40 9/16 – 3/4 10 14.4 12.6 29.6 3.5 17.7 39 44.8 TBD TBD 700
FRB 355.xx.4.37.E 40 9/16 – 7/8 10 16.1 14 34 3.5 19.7 44.6 50.4 TBD TBD 620
FRB 320.xx.4.41.E 45 9/16 – 3/4 12 14.4 12.6 34.6 3.9 17.7 43.9 50.2 TBD TBD 760
FRB 355.xx.4.46.E 50 9/16 – 7/8 12 16.1 14 37.7 3.9 19.7 48.1 54.2 TBD TBD 1000
FRB 355.xx.4.55.E 60 9/16 – 7/8 12 16.1 14 37.8 3.9 19.7 48.4 54.8 TBD TBD 1100
FRB 400.xx.4.70.E 77 5/8 – 1 16 18.1 15.7 40.9 4.4 22.4 52.5 57.7 TBD TBD 1500
FRB 450.xx.4.70.E 77 3/4 – 11/8 16 20.3 17.7 40.9 4.4 23.6 57 62.2 TBD TBD 1650 | 1800
FRB 528.xx.4.70.E 77 7/8 – 11/4 16 23.4 20.8 42.7 4.4 27.9 57.7 65.1 TBD TBD 2800
FRB 528.xx.4.82.E 90 7/8 – 11/4 20 23.4 20.8 50.1 4.9 28 68.3 74.3 TBD TBD 2800
FRB 528.xx.4.100.E 110 7/8 – 11/4 25 23.4 20.8 50.7 5.5 28 68.6 75.3 TBD TBD 2800
FRB 528.xx.4.105.E 115 7/8 – 11/4 25 23.4 20.8 52.1 5.5 28 67.6 77.1 TBD TBD 3850
FRB 528.xx.4.137,5.E 150 7/8 – 11/4 32 23.4 20.8 54.6 6.3 28 69.8 79.9 TBD TBD 3150
FRB 575.xx.4.137,5.E 150 15/16 – 11/4 32 25.6 22.6 55.6 6.3 30.3 72.2 82.1 TBD TBD 3000
FRB 670.xx.4.137,5.E 150 1 – 11/2 32 29.9 26.4 56.7 6.3 34.3 75.7 86 TBD TBD 3200

Minimum Ultimate Strength = 4 x WLL

  • The dimensions in this table are indicative only. A drawing will always be submitted prior to production and will be the leading document when discussing dimensions.
  • Blocks shown here are standard models; inquiries for custom versions are welcome.
  • Refer to wire rope manufacturers D/d ratio guideline.
  • Optional: Hook locking pin.

5-Sheave

Model No. WLL
(UStons)		 For Wire ød
(inch)		 Hook
Size		 Dimensions (inch) Weight (lbs)
øD1 øD2 B O TA TL L T øZ
FRB 355.xx.5.55.E 60 9/16 – 7/8 12 16.1 14 37.8 3.9 19.7 48.2 52.8 TBD TBD 1100 | 1280
FRB 360.xx.5.64.E 70 5/8 – 7/8 16 16.5 14.2 39.3 4.4 20.1 49.9 56.8 TBD TBD 1340 | 1550
FRB 360.xx.5.70.E 77 5/8 – 7/8 16 16.5 14.2 39.3 4.4 20.1 49.9 56.8 TBD TBD 1340 | 1550
FRB 360.xx.5.72.E 80 5/8 – 7/8 16 16.5 14.2 39.6 4.4 20.1 50.2 57.1 TBD TBD 1340 | 1550
FRB 400.xx.5.82.E 90 5/8 to 1 20 18.1 15.7 45.2 4.9 22.4 57 62.9 TBD TBD 1477 | 1540 | 1600 | 1800
FRB 400.xx.5.91 .E 100 5/8 to 1 20 18.1 15.7 45.2 4.9 22.4 57 65.2 TBD TBD 2250
FRB 450.xx.5.91 .E 100 3/4 – 1 1/8 20 20.3 17.7 46.7 4.9 23.6 59.9 67.9 TBD TBD 2250
FRB 400.xx.5.95.E 105 5/8 to 1 20 18.1 15.7 40.7 4.9 22.4 53.1 59.9 TBD TBD 2250 | 2870
FRB 400.xx.5.100.E 110 5/8 to 1 20 18.1 15.7 40.7 4.9 22.4 53.1 59.9 TBD TBD 2250
FRB 450.xx.5.100.E 110 3/4 – 1 1/8 25 20.3 17.7 49.7 5.5 23.6 62.9 69.6 TBD TBD 1900 | 2200 | 2250 | 2510
FRB 528.xx.5.100.E 110 7/8 – 1 1/4 25 23.4 20.8 49.9 5.5 28 65.9 74.6 TBD TBD 2500 | 2800
FRB 528.xx.5. 100.E 110 7/8 – 1 1/4 25 23.4 20.8 50.9 5.5 31.1 66 75.1 TBD TBD 2860 / 3960 / 5060*
FRB 575.xx.5.100.D 110 15/16 – 1 1/4 25 25.6 226 33.7 5.5 30.3 70.2 78.4 TBD TBD 2860 / 3960 / 5060*
FRB 528.xx.5.119.E 130 7/8 – 1 1/4 25 23.4 20.8 52.1 5.5 27.9 67.6 76.6 TBD TBD 3300
FRB 450.xx.5.125.D 137.5 3/4 – 1 1/8 32 20.3 17.7 50.7 6.3 23.6 63.7 72.1 TBD TBD 3630
FRB 528.xx.5.125.E 137.5 7/8 – 1 1/4 32 23.4 20.8 52.5 6.3 28 67.8 75.3 TBD TBD 3500 | 3960
FRB 450.xx.5.137.D 150 3/4 – 1 1/8 32 20.3 17.7 50.8 6.3 23.6 64.6 72 TBD TBD 3630
FRB 528.xx.5.137.E 150 7/8 – 1 1/4 32 23.4 20.8 54.4 6.3 28 69.8 79.7 TBD TBD 3500
FRB 670.xx.5.137.D 150 1 – 1 1/2 32 29.9 26.4 56.6 6.3 34.3 75.7 85.3 TBD TBD 6000*
FRB 630.xx.5.150.E 165 1 – 1 3/8 32 27.9 24.8 58.8 6.3 32.7 77.9 85.4 TBD TBD 4600 / 6100*
FRB 528.xx.5.160.E 176 7/8 – 1 1/4 40 23.4 20.8 59.1 7.1 28 77.9 86.3 TBD TBD 4000 | 4500
FRB 575.xx.5.160.E 176 15/16 – 1 1/4 40 25.6 22.6 62.6 7.1 30.3 79.2 87.5 TBD TBD 5500
FRB 630.xx.5.160.D 176 1 – 1 3/8 40 27.9 24.8 57.6 7.1 32.7 75.3 85.4 TBD TBD 5500
FRB 670.xx.5.160.E 176 1 – 1 1/2 40 29.9 26.4 62.6 7.1 34.3 81.1 92 TBD TBD 6000*
FRB 528.xx.5.182.D 200 7/8 – 1 1/4 40 23.4 20.8 58.1 7.1 27.9 73.4 86.5 TBD TBD 3860
FRB 575.xx.5.182.D 200 15/16 – 1 1/4 40 25.6 22.6 62.6 7.1 30.3 79.2 90.2 TBD TBD 5500
FRB 630.xx.5.182.E 200 1 – 1 3/8 40 27.9 24.8 62.3 7.1 32.7 79.4 89.8 TBD TBD 5500
FRB 670.xx.5.182.D 200 1 – 1 1/2 40 29.9 26.4 67.6 7.1 34.3 86.9 96.1 TBD TBD 6000*
FRB 630.xx.5.200.D 220 1 – 1 3/8 50 27.9 24.8 63.9 7.9 35.4 86.1 96.8 TBD TBD 5000 up to 15400*

* Removable cheek weights
Minimum Ultimate Strength = 4 x WLL

  • The dimensions in this table are indicative only. A drawing will always be submitted prior to production and will be the leading document when discussing dimensions.
  • Blocks shown here are standard models; inquiries for custom versions are welcome.
  • Refer to wire rope manufacturers D/d ratio guideline.
  • Optional: Hook locking pin.

6-Sheave

Model No. WLL
(UStons)		 For Wire ød
(inch)		 Hook
Size		 Dimensions (inch) Weight (lbs)
øD1 øD2 B O TA TL L T øZ
FRB 355.xx.6.55.E 55 9/16 – 7/8 12 16.1 14 35.8 3.9 19.7 46 52.4 TBD TBD 1496
FRB 360.xx.6.64.E 70 5/8 – 7/8 16 16.5 14.2 38.3 4.4 20.1 48.9 50.3 TBD TBD 1495
FRB 400.xx.6.64.E 70 5/8 – 1 16 18.1 15.7 41.9 4.4 22.4 53.7 60.5 TBD TBD 1700
FRB 400.xx.6.82.E 90 5/8 – 1 20 18.1 15.7 45.2 4.9 22.4 57 62.9 TBD TBD 1800
FRB 450.xx.6.82.E 90 3/4 – 11/8 20 20.3 17.7 46.7 4.9 23.6 62.2 68.1 TBD TBD 2000
FRB 400.xx.6.91.E 100 5/8 – 1 20 18.1 15.7 44.6 4.9 22.4 56.4 64 TBD TBD 2200
FRB 450.xx.6.100.E 110 3/4 – 11/8 25 20.3 17.7 49.7 5.5 23.6 62.9 69.6 TBD TBD 2500
FRB 528.xx.6.100.E 110 7/8 – 11/4 25 23.4 20.8 50.1 5.5 28 64.9 73.4 TBD TBD 2500
FRB 450.xx.6.120.E 132 3/4 – 11/8 25 20.3 17.7 47.9 5.5 22.4 59.8 68.1 TBD TBD 2200
FRB 528.xx.6.137.E 150 7/8 – 11/4 32 23.4 20.8 52.5 6.3 28 67.8 77.8 TBD TBD 3500
FRB 528.xx.6.150.E 165 7/8 – 11/4 40 23.5 20.8 61.1 7.1 28 79.5 87.9 TBD TBD 4000
FRB 528.xx.6.160.E 176 7/8 – 11/4 40 23.5 20.8 62.2 7.1 28 77.8 86.1 TBD TBD 4500 | 5000
FRB 528.xx.6.182.E 200 7/8 – 11/4 40 23.5 20.8 63 7.1 28 79.5 87.9 TBD TBD 4500
FRB 575.xx.6.182.E 200 15/16 – 11/4 40 25.6 22.6 61.1 7.1 30.3 77.4 88.4 TBD TBD 4500 | 5500
FRB 670.xx.6.182.E 200 1 – 11/2 40 29.9 26.4 61.7 7.1 34.3 80.2 90.2 TBD TBD 5500
FRB 528.xx.6.200.E 220 7/8 – 11/4 50 23.5 20.8 63 7.9 28 79.5 87.9 TBD TBD 5500
FRB 575.xx.6.209.E 230 15/16 – 11/4 50 25.6 22.6 65.4 7.9 30.3 81.9 91.2 TBD TBD 6500

Minimum Ultimate Strength = 4 x WLL

  • The dimensions in this table are indicative only. A drawing will always be submitted prior to production and will be the leading document when discussing dimensions.
  • Blocks shown here are standard models; inquiries for custom versions are welcome.
  • Refer to wire rope manufacturers D/d ratio guideline.
  • Optional: Hook locking pin.

7-Sheave

Model No. WLL
(UStons)		 For Wire ød
(inch)		 Hook
Size		 Dimensions (inch) Weight (lbs)
øD1 øD2 B O TA TL L T øZ
FRB 355.xx.7.75.E 82.5 9/16 – 7/8 16 16.1 14 39.2 4.4 18.9 49.8 56.8 TBD TBD 1600
FRB 400.xx.7.100.E 110 5/8 – 1 20 18.1 15.7 43.6 4.9 22.4 55.6 63.4 TBD TBD 2400
FRB 400.xx.7.118.E 130 5/8 – 1 25 18.1 15.7 48.9 5.5 22.4 60.9 69.4 TBD TBD 2400
FRB 400.xx.7.127.D 140 5/8 – 1 32 18.1 15.7 47.8 6.3 22.4 59.8 68.3 TBD TBD 2850
FRB 450.xx.7.127.E 140 3/4 – 11/8 32 20.3 17.7 54.3 6.3 23.6 67.4 76.9 TBD TBD 3150
FRB 450.xx.7.137.E 150 3/4 – 11/8 32 20.3 17.7 54.3 6.3 23.6 67.4 76.9 TBD TBD 3100
FRB 450.xx.7.160.D 176 3/4 – 11/8 40 20.3 17.7 58.2 7.1 23.6 71.4 80.8 TBD TBD 3930
FRB 528.xx.7.160.D 176 7/8 – 11/4 40 23.4 20.8 58.6 7.1 31.1 73.9 83.5 TBD TBD 3300 / 4950 / 6600*
FRB 575.xx.7.171.D 188 15/16 – 11/4 40 25.6 22.6 56.8 7.1 30.4 72.7 82.6 TBD TBD 5940
FRB 528.xx.7.182.E 200 7/8 – 11/4 40 23.4 20.8 59.5 7.1 27.9 74.3 85.4 TBD TBD 6160
FRB 528.xx.7.200.D 220 7/8 – 11/4 50 23.4 20.8 58.8 7.9 27.9 74.3 84.2 TBD TBD 5280
FRB 575.xx.7.209.D 230 15/16 – 11/4 50 25.6 22.6 59.9 7.9 30.3 76.4 87.4 TBD TBD 6500 | 7500
FRB 575.xx.7.209.D 230 15/16 – 11/4 50 25.6 22.6 59.9 7.9 30.3 76.4 87.5 TBD TBD 5500 / 7500 / 8500*
FRB 575.xx.7.209.D 230 15/16 – 11/4 50 25.6 22.6 59.9 7.9 30.3 76.4 87.5 TBD TBD 5500 / 7500 / 9500*
FRB 670.xx.7.209.D 230 1 – 11/2 50 29.9 26.4 63.1 7.9 34.3 82.2 93.1 TBD TBD 6500*
FRB 670.xx.7.228.D 250 1 – 11/2 50 29.9 26.4 63.1 7.9 34.3 82.2 93.1 TBD TBD 6500 | 7700*
FRB 670.xx.7.250.DB 275 1 – 11/2 63 29.9 26.4 64.6 8.8 34.3 83.8 99.5 TBD TBD 10000*
FRB 528.xx.7.272.D 300 7/8 – 11/4 63 23.4 20.8 61.8 8.8 27.9 77.2 88.8 TBD TBD 6450

* Removable cheek weights
Minimum Ultimate Strength = 4 x WLL

  • The dimensions in this table are indicative only. A drawing will always be submitted prior to production and will be the leading document when discussing dimensions.
  • Blocks shown here are standard models; inquiries for custom versions are welcome.
  • Refer to wire rope manufacturers D/d ratio guideline.
  • Optional: Hook locking pin.

WARNING: Prop 65: Products supplied by CERTEX USA may expose you to chemicals including Nickel, which is known to the State of California to cause cancer. For more information, visit to www.P65Warnings.ca.gov.

Related Products

Associated Wire Rope Snatch Blocks

Associated Wire Rope Snatch Blocks

Ropeblock Snatch Blocks are an excellent choice in most rigging and lifting plans. Durability and ease of use are some of the key benefits in addition to: Design Factor of Safety of 4:1 Lubricated bronze bushings Eye or oblong eye connection Sheaves, featuring...

Associated Wire Rope Standard Reeve Crane Blocks

Associated Wire Rope Standard Reeve Crane Blocks

Blocks shown in this section may be used on a wide variety of land based cranes such as mobile and crawler cranes. Standard Reeve Blocks are an excellent choice where frequent easy block change is not a required main feature, or lifting height is limited: Double...

Associated Wire Rope Round Overhaul Balls

Associated Wire Rope Round Overhaul Balls

The weight of the overhaul balls in this segment are based on average boom lengths and efficiency loss in mobile and crawler cranes. The low friction and easy to access hook swivel design makes the OHB series an excellent choice for a wide variety of crane...

Associated Wire Rope Overhaul Balls

Associated Wire Rope Overhaul Balls

The weight of the overhaul balls in this segment are based on average boom lengths and efficiency loss in mobile and crawler cranes. The low friction and easy to access hook swivel design makes the OHB series an excellent choice for a wide variety of crane...